Single post

How To Install Carpet

carpet_installers

An easy and inexpensive way to finish and cover the floors throughout your house is to install some carpet. A great advantage is the fact that carpets can be found at your local store in a wide variety of colors and models, which makes it easy to find one that compliments your style and your house. Carpet also will help keep your house warm because it will work as insulation too. besides carpet keeping your house warmer the carpet also considerably improves the protection against the sound produced by steps. Overall, it seems like a cheap comfort worth taking into consideration. Installing the carpet is just as easy. You don’t need a degree to do it, but just a few tools, patience and maybe a friend to give you a hand.

Things you will need

In order to start installing a carpet, there are a few things you will need. It is better to get everything around you since the beginning, rather than running to the store in the middle of the project. Here is what you will need:

  • Carpet
  • Cask
  • Tape line
  • Professional floor cleaner
  • Clean cloths, sponges or other cleaning “tools”
  • Priming
  • Adhesive
  • Teeth based scraper
  • Rubber roll
  • Scissors
  • Plinth

To make the whole operation easier and more fun, a friend can be very handy. A radio may also be a good idea.Steps to follow

    1. Check out the surface of the room you are preparing to install the carpet in. It has to be plain. Only then the carpet can be applied correctly. Use a cask to verify that. If you notice slight level differences, you will need to add an auto leveling screed first. Once it is set up, double check to make sure you can go on with the installation.
    2. Measure the room. Use a tape line for this operation and again, double check. Time to get to the store then. Purchase at least 10 percent more carpet than what you actually need. If you haven’t done such operations before, there is a chance to make minor mistakes or cut it incorrectly, so allow a margin for errors. If you want to realize a correct installation, do it like experts. Bring the carpet in the room about 8 hours before actually starting the operation. This way, you avoid condensation, which makes the whole mounting very difficult.
    3. Clean the floor accordingly. Use a professional cleaner. If your house is new and you still got dust and debris, you might want to do it multiple times. Get the big pieces today, clean it out tomorrow and clean the remaining dust again the day after tomorrow. The surface must be perfectly clean before being covered with carpet. Remove any sign of grease, dust or dirt.
    4. Apply the priming once you are done with the cleaning. You need to do it on the entire surface of the room. Use a brush and take your time. According to the type of priming you get, you will have to let it dry for a while. It is not a general time, just check out the instructions on the label and stick to them. You may even wait a couple of extra hours just to make sure it is completely dry.
    5. Get the adhesive on the priming. Most experts recommend using a special adhesive for carpets. Such products don’t have any solvents or unpleasant smells. According to the width of the carpet roll and the overall surface of your room, you must apply the adhesive only on one side of the contact area. Start with one of the margins of your room and apply in all the directions with a teeth based scraper that automatically adjusts the necessary quantity. After applying, leave the adhesive for 5 to 10 minutes to aerate before you actually set up the carpet.
    6. Set up the carpet and press it progressively with a clean, rubber roll. The way you use the rubber roll determines the final look. This is the part where you could use a friend to make sure you put it down correctly. It is imperative to use the rubber roll from the center to the margins. This way, there are no air bubbles left under the carpet and therefore, no wrinkles. Perform this operation multiple times, not just once. When the entire surface of your room is covered, get the scissors and cut the extra material left on the margins. Do it progressively. Randomly cut large parts, then do it carefully as you get closer to the margins. Everything is easier then. If you try to cut it off directly from one shot, you might do it unshapely.
    7. Your final step is to mount the plinth. After about 30 to 60 minutes, the adhesive is dry and the plinth is ready to go. Most plinths, whether they are made out of wood, PVC or other materials, have a very easy to understand clamp catching system. The material for the plinths only depends on your preferences. Each has advantages and disadvantages.

installing carpet

Tips and tricks

To avoid any small wounds, you should consider some protective gloves too. The plinths are sometimes sharp, while the adhesive can cause various wounds to your hands and obviously you can’t run to wash them off while the adhesive is half applied.

If you own a small room and you want a faster solution, you can use dual adhesive band. Besides, it is a very efficient method for the parquet based boards that require a temporary carpet, without ruining the existing support. The dual adhesive band is applied on the back of the carpet, eliminating the risk of moving. You can usually find it in commerce as rolls.Conclusion

Installing a carpet is not such a hard task, and doing the carpet installation yourself can save some much needed money. It can actually be a very fun activity that will pay for itself every night while you watch TV. The great advantages of carpet – thermic and phonic insulation – recommend it for all the rooms where the accent is placed on comfort. Therefore, if you decide to go on with it, it is absolutely necessary to do it accordingly.

LEAVE A COMMENT